Airmar P65 Uživatelský manuál stáhnout pdf

17-293-01 rev. 02 04/12/11

Transom Mount with Integral Release Bracket

Transducer or TRIDUCER® Multisensor

Model: P65

Applications

• Not recommended for boat with large inboard engine(s).

• Designed for high speed operation up to 55kn (63MPH)

• Vertically orients sound beam on hull with deadrise angle up to 30°

• Adjusts to transom angles from 3

° –20°

Tools & Materials

Safety goggles

Dust mask

Pencil

Screwdrivers

Electric drill

Drill bit, hole saw or spade bit for:

Bracket holes 4mm, #23, or 9/64"

Fiberglass hull chamfer bit (preferred), 6mm, or 1/4"

Transom hole (optional) 20mm or 13/16"

Cable clamp holes 3mm or 1/8"

Masking tape

Straight edge

Marine sealant (suitable for below waterline)

Zip-ties

Water-based antifouling paint (mandatory in salt water)

Mounting Location

CAUTION: Do not mount in an area of turbulence or bubbles:

near water intake or discharge openings; behind strakes, struts,

fittings, or hull irregularities

CAUTION: Avoid mounting the sensor where the boat may be

supported during trailering, launching, hauling, or storage.

• For the best performance, the sensor must be in contact with

smooth water. To identify an area of clean water, observe the

water flow off the transom while the boat is underway.

• Allow headroom space above the bracket for it to release and

rotate the sensor upward.

• Mount the sensor as close to the centerline (keel) of the boat as

possible to ensure the sensor remains in the water when the

boat is turning.

• Single drive boat—Mount at least 75mm (3") beyond the

swing radius of the propeller (see Figure 1). The starboard side

where the propeller blades are moving downward is preferred.

• Twin drive boat—Mount the sensor between the drives.

Figure 1. Mounting location on single drive boat

75mm (3")

minimum beyond

swing radius

INSTALLATION INSTRUCTIONSOWNER’S GUIDE &

Follow the precautions below for optimal product

performance and to reduce the risk of property

damage, personal injury, and/or death.

WARNING: Always wear safety goggles and a dust

mask when installing

WARNING: When the boat is placed in the water,

immediately check for leaks around the screws and

any other holes drilled in the hull.

CAUTION: Bracket protects the sensor from frontal

impact only.

CAUTION: Never pull, carry, or hold the sensor by the

cable as this may sever internal connections.

CAUTION: Never strike the sensor.

CAUTION: Never use solvents. Cleaners, fuel, paint,

sealants, and other products may contain strong

solvents, such as acetone, which attack many plastics

greatly reducing their strength.

IMPORTANT: Please read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

Record the information found on the cable tag for future reference.

Part No._______________Date___________Frequency__________kHz

1 2 3 4

Shrnutí obsahu

Strany 1 - Mounting Location

17-293-01 rev. 02 04/12/11Transom Mount with Integral Release BracketTransducer or TRIDUCER® MultisensorModel: P65Applications• Not recommended for bo

Strany 2 - Installation

2Plastic Shim• If you know the transom angle of your boat (see Figure 3):• Standard transom (13° transom angle)—The bracket is designed for a standard

Strany 3 - Antifouling Paint

3Cable RoutingCAUTION: Do not remove the connector to ease cable routing. If the cable must be cut and spliced, use Airmar’s splash-proof Junction Box

Strany 4 - TECHNOLOGY CORPORATION

4Sensor Replacement & PartsThe information needed to order a replacement sensor is printed on the cable tag. Do not remove this tag. When ordering

Komentáře k této Příručce

Žádné komentáře

Airmar P65 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Airmar P65. Airmar P65 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Senzory Airmar P65